The Ship Model Forum

Oh ok awesome. I thought so, I thought it was only to make only the PoW when she fought the Bismarck

Looking at the instructions, I believe you can make either version.

Can you make the PoW from the Force Z refit with the PoW update set or just as she was when she fought the Bismark???

Dear Mr. Kim
I would like to asking you if is possible to buy the Duke of York details set in SMW 2015 Telford on 7 November.
Could you please tell me if it is possible or not.
Thanks in advance
Symeon.

If you emailed with derytele..., please email again with other account.
derytele ejected our email.
Thank you
Keumho Kim

Hi there,

Is there is any chance i might order replacement parts (2) for 1/350 Prince of Wales kit?

Thanks

Can you show me some photos?
I cant understand with your post.
or contact me via email.
Thank you
Keumho Kim

I've bought the PoW set. There was a problem with the brass barrels of the 2nd turret (the twin turret.) Whenever it is mounted in triple or quadruple there isn't a problem, but the twin mounting caused one barrel to stuck and couldn't go fully down while another one could. Is that happens with your build?

Regards.

Re: The Ship's Bell location.
From two IWM photos of the bell, one of it being rung by a coxswain and another showing a Royal Marine Bugler with it in the background, it was hanging below a carley float just forward of an open scuttle. The only place on the main deck where they had these was along the outside of the Wardroom Flat, technically, part of the quarterdeck. The scuttle hinge is to the left and, as the hinges were at the forward edge, this means it was the "Port" or left side of the ship. So, my choice of position is just aft of, and above, the aft-most scuttle on the port side of the wardroom flat where it lies parallel with the side of the ship.

I think we can spot it on this still I captured from a cine-film taken from a boat passing KGV at anchor.

Most grateful for the update Mr Kim. Thank you.

Postscript: Purchased the 1/350 Revell Bismarck set and it exceeds expectations in every way. Thank you Mr. Kim for your commitment to quality!

We try to release at this October
Thank you
Keumho Kim

I think over 70% can be used for the later KGV with our detail set.
Thank you
Keumho Kim

Hello Mr. Kim,
Yet another year has passed since this response which referenced a 2012 reply. What are the prospects for the Revell 1:350 Bismarck for the remainder of 2014?

I know this post is old, but is there any chance of seeing the late KGV version? I want to build a 1945 version and would like to have a Pontos kit. If not, how much of the 1941 KGV kit could be used on a later fit?

Thanks,
Chris

Same question,bell is attached to part 380,but where it must go?

Can anyone tell me where the ships bell goes?

Hi Kim,
Sorry, every time you make something, I ask for something more! As the Americans say, I am like a "kid in a candy store".

Well there have been too many askings to release 1/350 20mm Oerlikon single/Twin 25mm IJN single/Twin/triple 8 pompom /quad Pompom and same for 1/200 and so on that were developed already by Pontos.

But now we are focusing on firstly on the full detail sets promised to you.
So just wait some more for these unit sets.

Thank you
Keumho Kim

Hi Kim,
Thanks for the reply. I am disappointed that it won't be available as a separate item to buy.
Have you thought about doing a p/e and brass set (including the quad pom pom) for the Trumpeter 1/350 Tribal destroyers as they need some help? They come with an eight barrelled pom pom which should be a quad.

I will try to design and make quad pompom soon.
A small PE may be enough and we will distribute this only with actual shipping cost 1USD to our 35015F1 Prince of Wasles owner.

Kim