| The Ship Model Forum http://shipmodels.info/mws_forum/ |
|
| USS Forrestal CV 59 1/700 http://shipmodels.info/mws_forum/viewtopic.php?f=60&t=356674 |
Page 1 of 1 |
| Author: | Christoph Mentzel [ Sat Jun 04, 2022 8:51 am ] | |||||||
| Post subject: | USS Forrestal CV 59 1/700 | |||||||
The 3 d printed USS Forrestal
|
||||||||
| Author: | MartinJQuinn [ Sat Jun 04, 2022 9:20 am ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
Nice work, Christoph! |
|
| Author: | Jim B [ Mon Jun 06, 2022 10:07 am ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
Great job. Very well done. |
|
| Author: | Pieter [ Thu Jun 09, 2022 5:01 am ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
Nice work. How is working on these 3D kits compared to injection molded kits and resin kits? |
|
| Author: | ModelMonkey [ Thu Jun 23, 2022 8:13 am ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
Wonderful! |
|
| Author: | ABH2USN Varnell [ Sat Aug 27, 2022 6:26 pm ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
Amazing work there, very nice 
|
|
| Author: | actech80 [ Fri Sep 16, 2022 11:36 pm ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
So these are pictures of an actual 1/700 scale Forrestal that is 3D printed. Where and how can I purchase one !!!! I would also like to find a 1/700 Coral Sea CVA-43 , and get 3D CVA-59 , 60 , 61 , and 62. actech80 |
|
| Author: | Pieter [ Mon Sep 19, 2022 6:01 am ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
They show up at a certain auction site. Note that the plastic used in these 'kits' is different from regular injection molded kits and resin kits. Most relevant if building them is that it tends to be more brittle. |
|
| Author: | maxim [ Sat Oct 08, 2022 8:42 am ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
Impressive model! @ Christoph: were all parts of the kit printed in the same quality or were e.g. the small parts printed in a better one? I am asking, because the smaller models by Gaga (South Korean destroyers and frigates) are printed in very good quality, but e.g. the larger HMS Implacable is printer in a lower quality. |
|
| Author: | Christoph Mentzel [ Sun Oct 09, 2022 2:46 am ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
The quality of the small parts was not really convincing. I replaced most of them (armament and radar). The finish of the print is really good. |
|
| Author: | maxim [ Mon Oct 10, 2022 11:22 pm ] |
| Post subject: | Re: USS Forrestal CV 59 1/700 |
Thank you for the reply! Nick did also replace all the small parts in case of his Implacable model. |
|
| Page 1 of 1 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|