I was rather surprised to see that you stuck the veneer onto to the paint. I would be a bit concerned that due to changing humidty the veneer starts warping and come off. How did you sand it down and varnish it without spoiling the surrounding paintwork ?
wefalck
Re: EX NAVAL TUG .TID 164
Posted: Mon May 28, 2012 12:35 pm
by Tiny69
To answer your question, I haven't.
Tiny
Re: EX NAVAL TUG .TID 164
Posted: Sun Jun 03, 2012 12:38 pm
by Tiny69
I have been concentrating on painting various fittings in the wheelhouse and the black areas on the superstructure. Also I have been wiring the LED lights in the mast and routing the wires inside the superstructure.
Tiny
Re: EX NAVAL TUG .TID 164
Posted: Thu Jun 07, 2012 12:26 pm
by ARH
Have a good day on your birthday tomorrow, take plenty of photo,s at York Railway Museum for the site.
Re: EX NAVAL TUG .TID 164
Posted: Fri Jun 08, 2012 4:55 am
by Dave Wooley
Hi Tiny Ron mentions that its your Birthday tomorrow ,All the very best to you !!!. Have a good visit to the York Railway Museum , it's not just rolling stock but "SHIP" Models and lots of them as well , as Ron says photos please!!!!!
Dave Wooley
Well done Tiny, looks like you had a good day, like you said, that fire box on Pricess Elizabeth was well worth standing in front of.
Re: EX NAVAL TUG .TID 164
Posted: Sat Jun 16, 2012 8:16 am
by Tiny69
Lighting
With all the LED lights fitted and the wires routed around the inside of the superstructure all that was left to do was to solder each one to the 6v battery/resistor module I had made. Using a 15W soldering iron each wire was soldered in place ensuring the correct polarity was maintained. Finally all the soldered joints where covered with two part epoxy glue to ensure that the joints would not be effected by any moisture.
Tiny
Re: EX NAVAL TUG .TID 164
Posted: Mon Jun 18, 2012 4:15 am
by Dave Wooley
Hi Tiny Just catching up with your build. Lighting for models is one of those tasks where there is a thin line between being just right or over the top. You have that ability of getting things just right . Excellent work throughout.
Dave Wooley
Re: EX NAVAL TUG .TID 164
Posted: Sat Jun 23, 2012 4:56 am
by Tiny69
Ballasting
Time to fill the internal testing tank or bath to everyone and ballast out the boat. First I put the hull in the water and placed the steam plant inside with the boiler filled with water. Now I could add weight using cast metal sticks each weighing 225g (8oz) each and place them inside triming up the hull so it sat correctly on the water. With the steam plant in place I added 8 sticks in total, which is 1800g almost 4lbs.
Next I removed the steam plant and inserted the electric module, which is lighter, so had to add an additional 4 sticks increasing the ballast to 2700g (6lbs Approx.) I permenately glued the ballast in for when I use the steam plant and left the extra weights loose so they can be easily placed inside when using thew electric module.
Tiny
Click on the link below for a short video of the steam enigine working in the test tank
ARH and Tiny prepare to launch the TID tug as part of our Model ship building society seminar and yes it is under live steam .
the boiler room
Underway under its own steam!!
A great day for Tiny and ARH
Dave Wooley
I would just like to thank Dave for the great photos he has taken of the day.
Oh and my dad for taking the video.
Tiny
Re: EX NAVAL TUG .TID 164
Posted: Tue Jul 10, 2012 12:08 pm
by Neptune
Been following all along, but haven't said anything up till now I guess.
Great build, it's "sharpness" is astonishing. Love that boiler system as well!
Re: EX NAVAL TUG .TID 164
Posted: Tue Jul 10, 2012 4:59 pm
by JIM BAUMANN
Certainly runs well!
Looks like it was a breezy day--even low doen in the lock....
Jim Baumann
Re: EX NAVAL TUG .TID 164
Posted: Wed Jul 11, 2012 7:57 am
by ARH
You are correct Jim, down near the river it was like a force 8 gail, the steam from the boiler could hardly be seen, it was blown away very fast from the funnel, she did sail well and all credit to Tiny's build.
Re: EX NAVAL TUG .TID 164
Posted: Thu Aug 30, 2012 2:05 pm
by Tiny69
I haven't posted for a while but on Saturday (25th August 2012) I spent the day at Chatham Dockyard with the "Friends of TID164" and Mike Toms showed me around their TID tug and I would like to thank them for their hospitality and guided tour. It was a great opportunity to meet the people who keep this little vessel going and I thoroughly enjoyed it. I was so impressed with their efforts I presented them with a copy of my book on the build of my model. They loved the book and it now sits in the mess for all to read. Keep up the good work and I hope to see her in full steam very soon.
