The Ship Model Forum

I present to you today my build of the Mogami in its Light cruiser configuration.



The kit is made by Tamiya, which means it's nice and I don't expect any major assembly problems.

However, some details are missing and the flak parts are really too crude. You get the feeling that Japanese manufacturers have pooled their efforts on these clusters and that they're showing their age...



So we're going to add some trinkets:

the 2 Artist Hobby PE sets (the only ones for the ship in this configuration)



A PE board for the lino deck battens, as on my 1/350 Maya, but this time at 1/700... yes I know, I'm a nut



127mm turrets in 3D :



The 20mm triple :



Back to work!

Here's the deck, very pleasant engraving, but we're going to get rid of all that

The paravans have been removed too, replaced by 3d versions.












And the shadoks sanded and sanded... and when they weren't sanding, they slept dreaming that they were sanding...











To go faster, in addition to the "classic" files, you can use this remarkably practical little tool !

It's long and tedious and progress is slow...






We're still making slow progress, but we're making progress... We're also adding some parts from the Artist Hobby detailing set

I don't think I've ever spent so much time on a deck...

The small plates are fitted...



Now we paint in Tamiya lino brown with my new gaahleri aero, very pleasant paint, the trigger is very soft and pleasant, and easy to clean.





We'll wait for it to dry completely and then start sanding shortly...

gentle scratching



with my electric sander, using the finest tip:



In this case, I didn't use the automatic option, in order to sand as softly as possible.

parafilm masking : Check

Next step : we attack the PE !!!!





For those who are still hesitating, it took me between 15 and 20 minutes to do the 3 bridges... how long will it take on the masking tape?

Before work this morning, we're sticking on something to improve tamiya's hopelessly flat fronts










all this fits on a tamtam pot with a radius of about 1.5m, of course.

in total: 18 pieces of PE for 2 pieces of plastic











Let's move on to the top floor with the bridge

Before :



remove the glass, sand it down and HOP! install the PE

After:





Blank laid on the tower, it will only be glued afterwards, to make it easier to paint.

Very nice work. I've always been curious about the Artist Hobby sets for these kits. Looks good. OTOH, I would never have the patience for the tie-down strips. Good for you.

It won't affect your build at all, but I just discovered that the Tamiya kits are 3.5mm too short.

Dan K wrote:Very nice work. I've always been curious about the Artist Hobby sets for these kits. Looks good. OTOH, I would never have the patience for the tie-down strips. Good for you.

It won't affect your build at all, but I just discovered that the Tamiya kits are 3.5mm too short.

Thanks Dan, I have to admit that I didn't measure the hull...
Anyway, it's going to be complicated to modify it!

Tha ArtistHobby sets are quite complete and easy to use, the PE parts are strong enough to be bend properly.

The next stage of the assembly is a very small one, but still, gluing the deck.
Not so easy, as the hull is very tight and the deck has to be held firmly during the gluing process to prevent it from popping out of its space...



mini overhang with gluing of 2 small railings and chimney grilles

I have to admit that I didn't measure the hull...

Nor should it have crossed your mind. We all assumed its correct. After all, it's a Tamiya kit. I found this out by accident while comparing it to a Fujimi version.

Continued good work.

Do you plan to add railings on the funnel itself? I never know, they always looks so overscale, but people still add them, may be it is ok...

Progress looks great, i didnt follow what is the trick with Parafilm? Why is it better than other solutions?

Dan K wrote:

I have to admit that I didn't measure the hull...

Nor should it have crossed your mind. We all assumed its correct. After all, it's a Tamiya kit. I found this out by accident while comparing it to a Fujimi version.

Continued good work.

Thanks Dan

pascalemod wrote:Do you plan to add railings on the funnel itself? I never know, they always looks so overscale, but people still add them, may be it is ok...

Progress looks great, i didnt follow what is the trick with Parafilm? Why is it better than other solutions?

The ArtistHobby set has no railings on the funnel

Regarding the parafilm, I find it easyer and much faster than the masking tape.
Also, as it has no glue on it, it can remain on the kit for very long periods without ruining the paint.

I made a tutorial (in french) here : https://www.laroyale-modelisme.net/t318 ... navire-uni

If you want I can make a translation

Despite the heat, we're making good progress, tackling a number of stages

The walkway around the chimney:








Some of the 155mm turrets: (for the moment, only 2 out of 5)

























Some of the platforms that will be receiving spotlights:

Excellent work so far, Yuth!

Questions:
- are you spraying ordinary acrylic paint on the styrene/brass surfaces without any preliminary priming? if so, how's the sticking of the paint/resistance to scratch? The pictures seem to suggest an optimal result.

- this is the first time i come across Parafilm M. It looks like an easy-to-apply material and you say it's time saver if compared to ordinary masking tape. would you give some advice/tips/do's and don'ts on how to use it?

Cheers,

SG

Hi SG

All the PE sheets have received some primer :


Regarding the parafilm, I made a tutorial here : https://www.laroyale-modelisme.net/t318 ... navire-uni

And you will find an english version here : viewtopic.php?f=4&t=404006

Thx!

Last night, assembly of the aft mast began



The mast is up, the crane has received a small piece of PE that required 5 Lilliputian bends
This ugly pellet has received a little putty to disappear:



Let's move on to the crane, which will be replaced by a PE version:





We're on a piece of hell...

Each horizontal section has three folds, as does each vertical section...
and, of course, despite taking every possible precaution, the sections did not stay together.
After several attempts and a great deal of swearing (some of it exquisitely original), I gave up and will resume work calmly this evening...

It takes a big dose of masochism, though!

Looking good! I especially admire you trying out those linoleum strips - one of the few PE parts that i still don't have the patience for.

brocken1sm wrote:Looking good! I especially admire you trying out those linoleum strips - one of the few PE parts that i still don't have the patience for.

You can continue to avoid them, they're out of scale and relatively hard to fit... the next models will have these painted bars

after a long summer break, let's go back to work


The original crane...





The PE was unusable, so it was replaced by a 3D-printed part made by my friend�@bgire

We're making progress on the turrets, but there are more PE than expected... 8 for the "classic" ones, 14 for those with telepointers ^^

We finished the weekend with the completion of the turrets, which was quite a big job!

Quick quiz: spot the odd one out!





And since I hadn't had enough PE, I tackled the walkway around the chimney by installing supports worthy of a quantum microscope...